Electrician referrals for Phoenix & nearby townsCall: (602) 584-7286
(602) 584-7286

Generator Installation in Glendale, AZ

electricianphoenixaz.net

Whole-house or essential-circuit backup: independent electricians near Glendale help you decide.

Need a transfer switch for your Glendale panel?
Call now to be connected with a local electrician in Glendale.
(602) 584-7286

Portable generators never plug into a wall outlet, and standby units connect through a transfer switch installed at the panel. The electrician also picks the pad location, fuel connection and circuits to back up. Call the number on this page to be connected with a local electrician in Glendale.

Standby generator beside a home, generator installation in Glendale, AZ

Three ways to tie a generator into a home

  1. An automatic transfer switch, used with standby units
  2. A manual transfer switch with a handful of chosen circuits
  3. A listed interlock kit with a generator inlet, used with many portables

Each keeps generator power from flowing back to the utility, which is the point of all three.

AC load is the sizing question

Central AC draws a large surge when the compressor starts, so a generator sized only for the running load may stall. Electricians check the AC's rating and may recommend a soft-start device to lower the surge. That one detail often decides whether a smaller unit works.

With a median build year of 1985, many homes here have older panels, so an electrician checks for room and breaker compatibility before planning a transfer switch.

Call now to be connected with a local electrician in Glendale.
(602) 584-7286

Useful local contacts for Glendale

Check the electric bill to see which utility serves the property; around the Valley it is most often APS or SRP. Outage reports go to that utility, which posts its numbers online.

Treat any fallen power line as live. APS and SRP both tell people to stay about 100 feet away and call 911. Inside the house, smoke or a hot burning odor from electrical equipment is also a 911 call, made from outside.

Permitted electrical work in Glendale is inspected by Glendale Building Safety. The contractor normally applies and schedules the inspection.

Ask for the contractor's ROC number and look it up on the Arizona Registrar of Contractors search before work begins. Residential electrical is the R-11 class; CR-11 covers both residential and commercial.

Work on the meter or service entrance also involves the utility, which controls the meter and must approve service changes. Your electrician coordinates that step.

Calls from Glendale are often matched with electricians who also cover Peoria, Sun City and Youngtown.

Placement affects labor

The farther the generator sits from the panel, the more wire and conduit the job needs, and trenching across a desert lot adds time. Code also sets distances from windows, doors and property lines. Choosing a good spot early can trim cost and avoid redoing work after the inspector visits.

If you already own a portable generator

Bring the model and the output plug type to the electrician. They can install a matching inlet and an interlock or transfer switch so the existing unit can safely power chosen circuits. Many portables work well with that setup, as long as they are sized for what you plan to run.

Fuel and fire safety

  • Let a portable generator cool before refueling
  • Store gasoline in approved containers away from the house
  • Keep propane tanks upright and outside
  • Keep brush and dry grass away from the unit

A hot generator on a dry desert lot calls for extra care.

Around Glendale

Calls come in from across Glendale, including around Loop 101, 51st Avenue, Mohawk Drive.

Catlin Court Historic District in Glendale is a National Register neighborhood subdivided in 1914 whose homes are mostly bungalows from that period, so older wiring is likely in the historic core.

Generator Installation questions in Glendale

How do I avoid carbon monoxide problems?
Run the generator outside and keep it far from openings. Put working CO alarms inside the home, and leave and call 911 if anyone feels ill.
How long does a generator installation take?
A portable inlet and interlock is often a single visit, while standby units involve permits, a pad, fuel connection and inspection, which stretches the schedule.
Can I install the transfer switch myself?
That is not a good idea. It involves working inside the panel and a mistake can start a fire or endanger others. A permit and an electrician keep it safe.
Does my home's age affect a generator hookup?
It can. Homes from the 1980s may need panel work before a transfer switch fits, which an electrician can judge on the first visit.

More electrical services in Glendale

Generator Installation nearby

Call now to be connected with a local electrician in Glendale.
(602) 584-7286

Last updated:

☎ Call (602) 584-7286